Important Plumber Guide for Installing a Bathtub
Important Plumber Guide for Installing a Bathtub
Blog Article
Right here down the page you'll find additional really good insight in regards to Tools You Need to Install a New Bathtub .
Setting up a bathtub isn't exactly rocket science, yet it does call for strong plumbing, carpentry, as well as in some cases, tiling abilities. Changing an old tub with a brand-new one is also a reasonably challenging job. If the old bathtub is readily easily accessible, the job can relocate rapidly; if you need to open up a wall surface to get rid of the old tub and position the new bath tub, the task is much harder. In either case, the job is within a house handyman's skills, although you will certainly need a helper to leave the old bathtub and also set in the new one. Ensure you have certified on your own for the task as well as fit trying it. As opposed to working with a specialist to take control of a halfway-completed task, it is better to think about using one prior to you begin. Opportunities are you may need an expert plumber to make tube connections.
This article will help you set up a new bathtub in your shower room if you have actually currently acquired a new bathtub and also do not need to transform the setup of your previous water supply pipes.
Your devices and product checklist should comprise the following:
Preparing for the Installment
To start with, the supporting frame provided with the bath ought to be fitted (if required) according to the maker's directions. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is important to make sure that if the faucet includes a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the faucets system to prevent stress on the bath tub.
Fit the versatile faucet ports to the bottom of both taps utilizing 2 nuts and also olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet via the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you make use of all of the provided washers.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom need to now be ready to be suited its final placement.
Removing Old Touches
If you require to change old taps with new ones as a part of your installation, after that the first thing you should do is detach the water. After doing so, switch on the taps to drain pipes any water remaining in the system. The process of getting rid of the existing faucets can be quite problematic due to the limited access that is commonly the case.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the taps. Have a fabric prepared for the staying water that will originate from the pipelines. When the supply pipelines have actually been eliminated, utilize the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from turning during this procedure. Once the taps have actually been removed, the holes in the bath/basin will certainly need to be cleaned up of any kind of old sealing compound.
Before carrying on to fit the new faucets, compare the pipe links on the old taps to the brand-new taps. If the old taps are longer than the new faucets, then a shank adapter is required for the new taps to fit.
Mounting the Bathtub
Using both wood boards under its feet, put the bath tub in the called for setting. The wood boards are helpful in uniformly spreading out the weight of the bathtub over the location of the boards rather than focusing all the weight onto four small factors.
The following goal is to ensure that the bathtub is leveled all round. This can be achieved by checking the level and changing the feet on the bath tub up until the level reviews degree.
To mount taps, fit all-time low of the outermost flexible tap connector to the suitable supply pipe by making a compression join; after that do the exact same for the various other tap.
Switch on the supply of water as well as check all joints and new pipework for leaks as well as tighten them if necessary. Fill up the tub and additionally check the overflow electrical outlet and also the normal outlet for leaks.
Lastly, take care of the bathroom paneling as explained in the maker's user's manual. Tiling and securing around the tub should wait up until the tub has been made use of at least once as this will resolve it into its last setting.
Suitable New Touches
If the tails of the new taps are plastic, then you will certainly require a plastic connector to stop damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the other end offers a connection to the current supply pipelines.
If you require to fit a monobloc, after that you will call for decreasing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, place the tap in the placing opening in the bath/basin ensuring that the washing machines remain in place between the tap as well as the sink. Safeguard the faucet in position with the supplier offered backnut. Once the tap is securely in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with typical tap adapters. The previous kind needs to be linked to the faucet finishes initially, tightening up just by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the area where the bathroom meets the tile, it is required to seal the joins with a silicone rubber caulking. This is important as the fitting can move sufficient to break a rigid seal, creating the water to penetrate the wall surface in between the bath as well as the tiling, bring about difficulties with wetness and feasible leaks to the ceiling listed below.
You can pick from a variety of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes as well as cartridges, and can sealing voids as much as a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with twists of drenched newspaper or soft rope. Remember to always fill the bath tub with water prior to securing, to enable the movement experienced when the tub remains in use. The sealant can crack rather early if you do not take into consideration this movement prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise easily offered on the market. It is recommended to fit the floor tiles making use of water-resistant or water-proof sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you really like reading about How to Install a Bathtub? Make feedback further down. We will be pleased to hear your thinking about this posting. We are looking forward that you visit us again before long. Sharing is caring. You won't know, you may be doing someone a favor. We value reading our article about How to Install a Bathtub.
Dial, we'll handle! Report this page